Arduino Nano RP2040 Connect with headers - ABX00053

Brand: Arduino
Product Code: AN-19486
Availability: Temporarily Out Of Stock

46.00€
Ex Tax: 38.02€

Qty

Another module from the Arduino Nano series is the first Arduino board created in collaboration with the Raspberry Pi. The Arduino Nano RP2040 Connect module is based on the Raspberry Pi RP2040 chip and is the first module to combine this chip along with additional sensors and connectivity on a single PCB. The board houses the aforementioned RP2040 chip, a 6-axis sensor IMU, a U-Blox Nina chip for WiFi and Bluetooth communication, as well as a microphone and an RGB LED. This version has soldered pin connectors.

Main features:

Interfaces: USB, SPI, I2C, I2S, UART, PWM
U-Blox Nina chip for WiFi / Bluetooth wireless communication
MicroUSB connector for computer connection and 5 V power supply
Built-in microphone, RGB LED and 6-axis IMU
Based on Raspberry Pi RP2040 microcontroller clocked at 133 MHz
Built-in 16 MB Flash memory and 264 kB SRAM
20 PWM pins, 8 analog pins and 22 digital pins
Standard dimensions for Nano series - 45 x 18 mm

Specification:

Power supply voltage: 4.5 V to 21 V
Operating voltage of logic part: 3,3 V
Output current 3.3 V: 800 mA
RP2040 microcontroller:

ARM Cortex M0 Dual-Core 133 MHz
264 kB SRAM
2 MB Flash
DMA controller
supports up to 16 MB Flash memory via QSPI bus
programmable IO (PIO) to support external peripherals
4-channel ADC with internal temperature sensor, 0.5 MSa/s, 12-bit conversion
SWD debugging

WiFi / Bluetooth module U-blox Nina W102:

dual core Xtensa LX6 240 MHz 32-bit
520 kB SARAM on-chip memory
448 kB ROM for boot and core functions
16 MB Flash memory for code storage, includes hardware encryption for program and data protection
1 kB EFUSE for MAC address, module configuration, Flash encryption and Chip-ID
IEEE 802.11 b/g/n 2.4 GHz WiFi
Bluetooth 4.2
built-in antenna (PIFA)
4 x 12-bit ADC
3 x I2C, SDIO, CAN, QSPI

Memory:

AT25SF128A 16 MB NOR Flash
532 Mb/s QSPI data transfer
100k programming / erase cycles

Sensor IMU 6-axis ST LSM6DSOXTR:

3D gyroscope:

± 2 / ± 4 / ± 8 / ± 16 g full scale

3D accelerometer:

± 125 / ± 250 / ± 500 / ± 1000 / ± 2000 dps full scale

advanced pedometer, step detector and step counter
Motion detection and roll detection
standard interrupts: free fall, 6D/4D orientation wake-up, click, double click
programmable finite state machine: accelerometer, gyroscope and external sensors
machine learning core
embedded temperature sensor

MEMS ST microphone MP34DT06JTR:

AOP = 122.5 dBSPL
signal to noise ratio 64 dB
omnidirectional sensitivity
frequency -26 dBFS ± 1 dB

RGB LED:

common anode
connected to U-blox Nina W102 GPIO

Microchip ATECC608A cryptographic chip:

cryptographic coprocessor with secure hardware key storage
I2C, SWI
Hardware support for symmetric algorithms:

SHA-256 and HMAC HASH including off-chip context saving/restoration
AES-128: encryption/decryption, Galois Field Multiply da GCM
internal high-quality random number generator NIST SP 800-90A/B/C

Secure boot support:

full ECDSA code signature validation, optional hash/signature
Optional communication key disablement prior to secure boot
Message encryption/authentication to prevent attacks

I/O:

14 x digital pin
8 x analog pin
microUSB
UART, SPI, I2C, I2S, PIO

Slot: microUSB
Operating temperature: from -20 °C to 80 °C
Dimensions: 45 x 18 mm

Tags: arduino, nano, rp2040, connect, with, headers, abx00053, controllers, original